Poulan 96194000506 Manual do Utilizador

OWNER'S MANUALMODEL NUMBER:96194000506SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read th

10TO MOVE FORWARD AND BACKWARD (See Fig. 14)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con

11TO ADJUST SKID PLATES (See Fig. 15)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

12OPERATIONTO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter

13GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

14MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

153. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 lockn

16SERVICE AND ADJUSTMENTS1. REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or f

17SERVICE AND ADJUSTMENTSSTORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more

18Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition

19ADVERTENCIA: Siempre desconecte el alambre de la bujía y póngalo donde no pueda entrar en contacto con la bujía, para evitar el arranque por acciden

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

204. Si la unidad empezara a vibrar de manera anormal, parar el motor y controlar inmediatamente para detectar la causa. Las vibraciones son generalm

21MONTAJE / PRE-OPERACIÓNPARTES EMPACADAS POR SEPARADO EL LA CAJA DE CARTÓN(1) CABLE DE ALIMENTACIÓN(198563)(1) CONDUCTO LA DESCARGA(3) RESORTES DE RE

22COMO PREPARAR SUMÁQUINA QUITANIEVES PORTAHERRAMIENTAS (Ver Fig. 8)Con su máquina quitanieves se le proporciona un portaherra-mientas. El portaherram

23MONTAJE / PRE-OPERACIÓNBIELA DE MANDO DE LA BARRENA BRAZO DE MANDO MANGUITO DE CAUCHO APERTURA GANCHO FIG. 5MONTAR LA BIELADE MANDO DE LA BARRENA (

24OPERACIÓNFAMILIARÍCESE CON SU MÁQUINA QUITANIEVESLEA ESTE MANUAL DEL DUEÑO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU MÁQUINA QUITANIEVES.Compare

25PALANCA DE CONTROL DE LATRAC-CIÓNOPERACIÓNCUMPLE CON LOS REQUISITOS DE SEGURIDAD DE LA A.N.S.I.Nuestras máquina quitanieves cumplen con los estándar

26OPERACIÓNLa operación de cualquier máquina quitanieves puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños grave

27USAR LA HERRAMIENTA PARA LIMPIAR(Ver Fig. 13) En ciertas condiciones de la nieve, el conducto de descarga pu-ede atascarse con hielo y nieve. Usar

28OPERACIÓNREGULAR LAS PLACAS DE DESLIZAMIENTO(Ver Fig. 15) NOTA: la llave de apriete proporcionada en su bolsa de partes puede utilizarse para regula

29OPERACIÓN• Asegúrese que la instalación eléctrica de su casa sea un sistema de tres hilos puesta a tierra de 120 Voltios A.C. Si no está seguro, co

36. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stoppe

30MANTENAMIENTORECOMENDACIONES GENERALESLa garantía de esta maquina quitanieves no cubre los artículos que han estado sujetos al abuso o a la negligen

31MANTENAMIENTOCORREAS EN VControlar el deterioro y el desgaste de las correas en V después de 50 horas de funcionamiento y sustituir si fuera necesar

32SERVICIO Y ADJUSTESADVERTENCIA: Para evitar lesiónes serias, an-tes de dar calquier servico o de hacer ajustes:1. Asegurarse el interruptor de ON/O

33SERVICIO Y ADJUSTES1. VACIAR LA GASOLINA DEL DEPÓSITO DE CARBURANTE – Vaciar la gasolina del depósito del carburante en un con-tenedor apropiado,

34ALMACENIMIENTODESMONTAR LAS RUEDAS (Ver Fig. 20)• Desmontar el perno de lingüete y desmontar la rueda del eje.IMPORTANTE: Cuando se instala la rued

35IDENTIFICACION DE PROBLEMASNo arranca 1. Válvula del combustible está OFF. 1. Gire a la válvula del combustible a la posición ON. 2. La llave

36REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 in

37REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 in

38NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

3911232301.07.024-BNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M

4PARTS PACKED SEPARATELY IN CARTONASSEMBLY / PRE-OPERATIONRead these instructions and this manual in its entirety before you attempt to assemble or op

40REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506CONTROL PANEL / DISCHARGE CHUTE12345667891111111001.09.001-AKEY PARTNO. NO. DESCRIPTION

41REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506CONTROL PANEL / DISCHARGE CHUTEKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensio

42REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use

43REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use

44REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506HANDLESKEY PARTNO. NO. DESCRIPTION 134565782910101001.12.001-BNOTE: All component dimen

45REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506HANDLESKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches.

46REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

47REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

48REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

49REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506CHASSIS / ENGINE / PULLEYSKEY PARTNO. NO. DESCRIPTION KEY PARTNO. NO. DESCRIPTION

5HOW TO SET UP YOUR SNOW THROWER TOOL BOX (See Fig. 8)A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. St

50NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

51NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

525314217689REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000506DECALS 1 181038 DECAL, DANGER 2 422041 DECAL, POULAN, 800S / 24" 3 181034

53SERVICE NOTES

54SERVICE NOTES

55SERVICE NOTES

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

8OPERATIONThrottle/engine control - used to se lect either FAST or SLOW engine speed and to STOP the engine.Traction drive control lever - used to eng

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas