Poulan 420904 Manual do Utilizador

OWNER'S MANUALMODEL NUMBER:PR5524ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the O

10OPERATIONTO THROW SNOW (See Fig. 14)The auger rotation is controlled by the auger control lever located on the right side handle.• Squeeze auger co

11TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

12COLD START - ELECTRIC STARTER1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the ke

13MAINTENANCELUBRICATION CHARTGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator

14MAINTENANCEV-BELTSCheck V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not ad just abl

15SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, before performing any service or ad- just ments:1. Be sure throttle is in STOP position.2.

16SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

17STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never

18TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.

19SERVICE NOTES

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

202 (EXPLODED)210911111312124131415178711561116183519212223242523222120362627283029313132333401.07.004-BREPAIR PARTS SNOW THROWER - - MODEL NUMBER P

21NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

22NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

23KEY PART NO. NO. DESCRIPTION12344301.11.001-AKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inche

24KEY PART NO. NO. DESCRIPTION12345667891111111001.09.001-ANOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORT

25NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

26NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

27NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

28NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

29NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

36. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel-ler and all moving parts have stopp

303129282627262530242444140403654894101112119941337394364384151416201921441718323334334224222444350495152535455566749515758526441273535652323235963616

31NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

32KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

33KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

34NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

36KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION1234586701.14.004-A1 198563 POWER CORD2 169675 RETAINER PIN3

37KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

38SERVICE NOTES

39SERVICE NOTES

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(3) RETAINER SPRINGS (169675)(1) TRACTION DRIVE CONTROL ROD(2) SHEAR BOLTS

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the ski

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

8OPERATIONChoke control - used for starting a cold engine.Drive speed control lever - used to select forward or reverse motion and speed of snow throw

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas